GE Appliance Repair in Windsor, Ontario

Er IF or Er rF error, cooling fault

Er IF points to an ice maker fan issue, Er rF to a refrigerator compartment fan fault. Both stem from a fan motor either jamming on ice buildup or wearing out electrically after years of steady use.

Fresh Food section running warm

GE fridges circulate cold air from the freezer into the fresh food section through a damper, and a stuck or failing damper motor is a very common reason one side stays warm while the other cools normally.

Water dispenser slow or not working

A partially frozen water line inside the freezer door or a clogged inline filter are both common causes, and GE's Precise Fit filters need replacing roughly every six months to keep flow consistent.

Loud buzzing or humming from the back

This is usually the compressor or condenser fan working harder than it should, often because the coils underneath or behind haven't been cleaned in years and are coated in dust.

IE error, won't fill with water

GE's fill error usually traces back to a kinked or partially closed supply hose, though a clogged inlet valve screen from mineral buildup is a close second, especially in homes without a water softener.

UE error, unbalanced load

Beyond genuinely uneven loads, worn suspension components or a leveling foot that's lost floor contact will trigger this error consistently, even with laundry spread evenly.

LD error, long drain

This means the washer is taking longer than expected to drain, almost always from a clogged pump filter or a partially blocked drain hose rather than a failing pump motor itself.

Washer leaking from underneath

A worn drain pump seal or a loose hose clamp are the most common sources, and leaks often only show up during the drain portion of the cycle, making them easy to miss until they've caused real damage.

E1 or E2 error, thermal fault

These codes point to a temperature sensing issue, either a shorted or open thermistor, and GE dryers will often limit or cut heat entirely as a safety precaution until it's resolved.

Dryer runs a full cycle but clothes stay damp

A blocked exhaust vent is the single most common cause across every dryer brand, and GE dryers move a substantial volume of air, so even a partial blockage noticeably extends drying time.

Burning smell during operation

This needs immediate attention rather than troubleshooting, since it can point to lint accumulation near the heating element or a genuine electrical fault, both fire risks if ignored.

Loud thumping with each rotation

Worn drum support rollers are the typical cause on GE dryers with several years of regular use, creating a rhythmic thump that gets louder as the flat spots on the rollers wear deeper.

Clean light flashing continuously

On most GE dishwashers a flashing Clean light after a completed cycle usually indicates the cycle didn't finish properly, often from a drain issue rather than the light itself being faulty.

Dishes coming out with grease film

Water temperature that's too low prevents grease from fully breaking down during the wash, sometimes from the home's water heater being set lower than the dishwasher expects.

Leaking from underneath the door

A worn or misaligned door gasket is the primary cause, and GE Profile models with the extra-large capacity design put slightly more stress on the seal than standard-size units.

Dishwasher won't start at all

A tripped door latch switch is a common and easy-to-overlook cause, the dishwasher simply won't run if it doesn't register the door as fully and securely closed.

Burner igniter clicks endlessly

Moisture or food debris around the igniter electrode causes continuous clicking on GE gas ranges, sometimes triggered by a boil-over that seeped down around the burner base.

F7 error, runaway oven temperature

This serious code means the oven's control system has detected temperature running away from the set point, and GE ranges will shut down heating entirely as a safety measure until addressed.

F3 error, oven sensor fault

Similar to other brands, this points to the oven temperature sensor reading incorrectly, either shorted or disconnected, and it commonly happens after the sensor probe shifts position during a rack change.

Electric coil element sparking when it heats up

This points to a damaged element or a worn receptacle underneath it, and it shouldn't be ignored since sparking coils can pose a genuine electrical hazard.

Oven takes unusually long to preheat

A weakening bake element loses efficiency gradually before failing outright, so the earliest sign is often just noticeably slower preheating rather than a total loss of heat.

F3 error, sensor fault

The same oven temperature sensor issue found on GE ranges applies to standalone wall ovens, and it's one of the more straightforward parts to diagnose and replace.

Convection fan not running during convection bake

A stalled or failing convection fan motor means the oven defaults back to standard heating patterns, leaving food unevenly cooked despite the convection setting being selected.

Self-clean cycle triggers an error and stops

Self-clean's extreme heat can expose a weak component that was otherwise holding up fine under normal baking temperatures, most often the door lock mechanism or a marginal sensor.